Tire Guide

Tire Maintenance Guide

A few minutes a month keeps tires wearing evenly and lasting longer. Here is what to check, how often, and what to look for, plus a quick tool that turns the date code on your sidewall into an age.

Quick Answer

Check pressure once a month with the tires cold, rotate them about every 5,000 to 6,000 miles, and replace them before the tread wears down to 2/32 of an inch. Look over the sidewalls each month and read the date code once a year.

  • Set pressure to the placard inside the driver's door, never the number on the tire.
  • Vibration usually points to balance; a pull or uneven wear usually points to alignment.
  • Older tires deserve a professional inspection even when the tread looks fine.
Back to the Tire Guide

Tire Pressure

Pressure is the single easiest thing to keep on top of, and it affects wear, handling, fuel economy and how much load a tire can carry safely.

A door-jamb tire placard beside a dial pressure gauge and a thermometer on a bench

Use the Door-Jamb Placard

The right number is on the placard on the driver's door jamb. It is set by the vehicle maker for your car, and it is listed cold, front and rear, sometimes with a different spare pressure.

Four-door sedan with a separate trunk and alloy wheels

Ignore the Sidewall Number

The larger pressure molded into the tire is its maximum, not a recommendation. Filling to that number makes the ride harsh and shrinks the part of the tread that touches the road.

Single tire without a wheel standing on a low tire stand

Check Monthly, and Cold

Check once a month and before long trips, after the car has sat for a few hours or has been driven less than a mile. Driving heats the air inside and raises the reading.

Dial tire pressure gauge with a braided hose and chuck

Know What the Warning Light Means

The tire pressure light usually comes on when a tire is about a quarter below its target. It tells you to check, not that a tire is flat. A light that flashes for about a minute at start-up and then stays on usually points to a sensor or system fault.

Snap-in tire valve stem shown large beside its cap and valve core

Maryland Weather Moves Your Pressure

Air pressure drops by roughly 1 psi for every 10 degrees Fahrenheit the temperature falls. After a cold snap or the swing between a warm afternoon and a frosty morning, a tire that read fine last week can be noticeably low. Top up with a gauge instead of trusting the eye, since a low tire can look almost normal.

Keep Learning:How To Read Your Tire Size

Tire Rotation

Front and rear tires wear at different rates. Front tires steer and, on most cars, carry the engine and do most of the braking, so they wear faster. Moving tires between positions keeps all four wearing evenly, so they last longer and grip alike.

Two wheels being swapped on a lift with an impact wrench and torque wrench

How Often

Many vehicle makers suggest every 5,000 to 6,000 miles, and shops often say every 3,000 to 5,000 miles or every 3 to 6 months. Your owner's manual has the final say. If you commute on I-495 or the Beltway, the miles add up quickly, so rotation may come around sooner than the calendar suggests.
VehiclePatternHow the Tires Move
Front-Wheel DriveForward CrossFront tires move straight back on the same side. Rear tires move forward and cross to the opposite side.
Rear-Wheel Drive and 4WDRearward CrossRear tires move straight forward on the same side. Front tires move back and cross to the opposite side.
All-Wheel DriveX-PatternEach tire moves to the opposite corner, front to the opposite rear and rear to the opposite front.
Directional TiresFront to Back, Same SideThe arrow on the sidewall must keep pointing forward, so tires only swap front and back on the same side.
Staggered Sizes (Wider Rear)Side to Side OnlyFront and rear sizes differ, so tires cannot change axles. Swapping sides works only on tires that are not directional and may require remounting.
Full-Size Matching SpareFive-Tire RotationOnly when your manual allows it: the spare joins the rotation so all five tires share the wear.

These are the common patterns. If your manual shows a different one, follow the manual, and let the shop know about any staggered setup, directional tires or a full-size spare before they start.

Balancing & Alignment

They sound alike and get mixed up all the time, but they fix different problems. Balancing is about weight around the wheel. Alignment is about the angles the wheels sit at.

A wheel on a balancing machine with a clip-on weight

Balancing

Small weights are attached to the wheel so the tire and wheel spin evenly. It is done whenever new tires are mounted and again if vibration shows up.

Clip-on wheel weight on a rim section beside strips of stick-on weights

Signs of an Imbalance

  • Shaking in the steering wheel at highway speed
  • Vibration you feel through the seat or floor
  • Scalloped or patchy wear on the tread

Alignment

Alignment sets the angles of the wheels so they point straight ahead and stand upright. Potholes, curbs and worn suspension parts can knock it out.

Tall five-door SUV with roof rails and alloy wheels

Signs of Poor Alignment

  • The car pulls to one side on a flat road
  • The steering wheel sits crooked when driving straight
  • Wear on one edge of a tire, inside or outside

Not Sure Which One You Need?

Vibration points to balance, and a pull or one-sided wear points to alignment. We handle rotation and balancing here. Wheel alignment is available by appointment. Book an alignment and pick a date at least 24 hours ahead.

Tread Depth

Tread is what moves water out from under the tire. As it wears, wet grip fades well before the tire looks bald.

Tread And Pressure Bench

10/32 in · Like New
35 psi · At The Placard

A 225/60R17 tire carrying an example 1,000 lb load on a glass footprint table. The gauge on the crown reads the depth of the center groove: 10/32 in when new, 4/32 in when it is time to plan ahead, and 2/32 in, the depth below which a tire fails a Maryland safety inspection, where the wear bars sit flush with the tread. The gauge on the valve stem reads the pressure, and the mirror under the glass shows the footprint: about 29 sq in at an example 35 psi placard, about 38 sq in at 26 psi, low enough for the warning light (it comes on near 26.3 psi, about a quarter below the placard), and about 23 sq in at a 44 psi sidewall maximum. Low pressure puts the load on the shoulders and high pressure puts it on the center. The tread is drawn 5 times deeper than scale so the wear shows.

Tread DepthConditionWhat To Expect
10/32 in or moreLike NewFull water-clearing ability and grip.
6/32 inGoodPlenty of life left, with wet grip starting to ease.
4/32 inPlan AheadWet-road grip is noticeably reduced. A good time to start planning replacement.
2/32 inInspection LimitAny less and the tire fails a Maryland safety inspection. Replace it now.

The Penny Test

A Lincoln penny makes a quick check that you can do in the driveway. It is not as exact as a tread gauge, but it will tell you when a tire is close to the end.

  1. 1Pick a GrooveChoose one of the main grooves running around the tire, away from any wear bar.
  2. 2Insert the PennyHold the penny with Lincoln's head pointing down and push the edge into the groove.
  3. 3Look at His HeadIf the tread covers part of the head, you have more than 2/32 of an inch. If all of the head shows, the tread is at or below 2/32 of an inch, and a tire below that fails a Maryland safety inspection.
  4. 4Repeat Around the TireTest the inside, middle and outside of each tire, since wear is often uneven.

Wear Bar Gauge

10/32 in · Like New

A cut section of tread drawn to scale: three ribs, two main grooves and a wear bar molded across each groove at 2/32 in. The bridge gauge stands on the ribs with its plunger on the groove floor, so it reads the depth that is left: 10/32 in on a new tire, 4/32 in when wet grip has dropped enough to plan a replacement, and 2/32 in when the ribs are flush with the bars, the depth below which a tire fails a Maryland safety inspection. The penny is held head down in the other groove, and at 2/32 in all of Lincoln's head shows.

Wear Bars Do the Same Job

Look for small raised bars across the bottom of the grooves. When the tread is level with them, the tire has reached 2/32 of an inch.

Under 2/32 Inch Fails a Maryland Safety Inspection

A tire with less than 2/32 inch of tread in a major groove fails a Maryland safety inspection, and so does one with cord or belt showing or a bulge. Wet-road grip has already dropped a long way by then. Many drivers replace at 4/32 inch so they are not caught out by heavy rain.

Keep Learning:UTQG Ratings Explained

Tire Age & the DOT Date Code

Rubber slowly hardens with heat, sun and time, even on a tire that hardly moves. The date code tells you when a tire was made, so you can judge age separately from tread.

DOT U2 LL LMLR205/55R16 91VTUBELESSRADIALMAX PRESS 51 PSI3221DOT U2 LL LMLR205/55R16 91VTUBELESSRADIALMAX PRESS 51 PSI3221DOT U2 LL LMLR205/55R16 91VTUBELESSRADIALMAX PRESS 51 PSI3221DOT U2 LL LMLR205/55R16 91VTUBELESSRADIALMAX PRESS 51 PSI3221
0°

How To Read the Code

Find the letters DOT on the sidewall, followed by a string of characters. The last four digits are the date: the first two are the week and the last two are the year. So 3221 means the 32nd week of 2021.

Single tire without a wheel standing on a low tire stand

Where To Look

The full number is usually on only one sidewall, so check the inside sidewall as well if you do not see it. Some tires end with a shorter, partial code, so look for the digits after the last group of letters.

Tire mounted on a five-spoke alloy wheel standing on rubber chocks

DOT Date Code Checker

Type the four-digit code, or the whole DOT number, and we will work out when the tire was made and how old it is today.

Four digits, week then year, such as 3221. You can also paste the whole DOT number.
Try an Example:

Date Code Result

Week 32 of 2021

32215 years, 3 months
DetailValue
Week32
Year2021
Made InThe week starting August 6, 2021
Age Today5 years, 3 months

Younger Than 6 Years

Age alone is not a concern at this point. Keep checking pressure, tread and sidewalls, and read the date code again once a year.

There Is No Single Cutoff

Vehicle and tire makers give different age guidance, often in the range of 6 to 10 years, and storage and use matter a great deal. Follow your vehicle and tire manufacturer's guidance, and ask a professional to inspect older tires.

Sidewall Damage & Repairs

Not every injury is the same. Some can be fixed properly and some mean a new tire, and you cannot judge the difference from the outside. This is a job for a professional, not a DIY fix.

Tire Repair Zones

Click Or Drag On The Tire, Or Use Arrow KeysTread PunctureOften Repairable
Often Repairable

A small puncture in the main tread area, away from the shoulder and sidewall, can often be repaired properly from inside the tire. A plug on its own is not a complete repair.

Single tire without a wheel standing on a low tire stand
Not Repairable

Bulges or bubbles, cuts or gouges that reach the cords, damage on the sidewall or shoulder, and tires that were driven flat generally cannot be repaired and need to be replaced.

Tire mounted on a five-spoke alloy wheel standing on rubber chocks

What To Look For

Single tire without a wheel standing on a low tire stand
  • A bulge, bubble or lump in the sidewall
  • Cuts, cracks or gouges, especially deep ones
  • Cords or fabric showing through the rubber
  • A tire that keeps losing air

A tire on the rollers of an inspection stand. The band outlined in green is the central tread, out to just past the outer grooves: industry guidance allows a puncture repair there for holes up to 1/4 in (6 mm), done from inside the tire with a patch-plug, which the section view shows. A plug on its own is not a complete repair. A puncture on the shoulder or sidewall, a bulge, or a cut that reaches the cords means a new tire. The zones drawn are typical; the tire has to come off the wheel and be checked from inside before anyone can say it can be repaired.

After a Pothole or Curb Hit

Maryland roads are rough after winter. If you have taken a hard hit, look the sidewall over and pay attention to any new vibration or pull. If in doubt, have a professional look at it, and avoid driving on a tire you are worried about.

Storage & Seasonal Swaps

Maryland does not require winter tires, but plenty of drivers run a second set for the coldest months, or swap for summer performance tires. Doing it right keeps the spare set in good shape.

Storing a Set

Single tire without a wheel standing on a low tire stand
  • Keep them in a cool, dry spot out of direct sun.
  • Stay away from electric motors and other sources of ozone.
  • Store unmounted tires upright, and tires on wheels stacked or hanging.
  • Bag or cover them if they sit outdoors, and note the date code before you put them away.

Making the Swap

Hydraulic floor jack with a raised lift arm and pump handle
  • Wash the tires and wheels, and check the tread and sidewalls before mounting.
  • Set the pressure to the door-jamb placard once they are on.
  • Check the wheel nuts are torqued to specification after the first drive.
  • Have the tires balanced if they are on their own wheels, or if you notice vibration.

Deciding Whether You Need a Second Set

Read the seasonal tires guide to see whether all-season, all-weather or a dedicated winter set makes sense for how and where you drive.

Keep Learning:Seasonal Tires Explained

Your Maintenance Schedule

Here is the whole routine in one place. Tap a button to book the visit or ask us a question.

TaskHow OftenWhat To Look ForNext Step
Check PressureMonthly, and before long tripsCold readings that match the door placard on all four tiresBook a Check
Rotate TiresEvery 5,000 to 6,000 miles, or per your manualEven wear front to back, on both sidesBook Rotation
Balance WheelsWith new tires, or when vibration startsShaking at highway speed or scalloped wearBook Balancing
Measure Tread DepthMonthly, and at every rotationDepth at or approaching 4/32 inch, or uneven wearBook a Check
Check AlignmentYearly, or after a hard impactA pull to one side or wear on one tire edgeAsk About Alignment
Inspect SidewallsMonthly, and after hitting a pothole or curbBulges, cuts, cracks or embedded objectsAsk About Repairs
Read the Date CodeYearly once tires reach 6 years oldThe week and year molded into the sidewallBook an Inspection
Seasonal SwapTwice a year, if you run two setsCondition and age of the stored setBook Tire Service

Keep Learning:More Questions? See Our FAQ

Frequently Asked Questions

It is on the placard on the driver's door jamb and often in the owner's manual. Use that number, checked cold, once a month. Do not use the maximum pressure printed on the tire sidewall.

Not Sure Where To Start?

Tell us your vehicle or tire size and we'll show you what fits. Browse the catalog, book a visit to our Upper Marlboro shop, or have us come to you.